 |
|
The SumiMark® Marking System is capable of printing on a wide range of heat-shrinkable tubing
types including general purpose polyolefins, dual wall tubings, high temperature PVDF and
flouroelastomers. SumiMark® tubing is made to the highest quality standards in the industry.
In addition to providing strain relief and insulation, it provides an excellent surface on which
to mark.
Tubing is supplied on continuous spools and is cut by the SumiMark® Marking System, allowing you
to create the exact length of marker needed, with no waste, resulting in tremendous inventory
savings. Diameters of 1/16" to 2" with shrink ratios of 2:1, 3:1 and 4:1 are available. There is
minimal longitudinal change after shrinking, so marks will not become distorted when installed.
SumiMark® tubing is available in black, white and colors in sizes ranging from 1/16" to 2"
and meet the respective military and commercial specifications (AMSDTL23053, UL, VW1, CSA).
SumiMark® ribbons are available in black, white and colors and are formulated to provide
a dry, instantly usable, permanent mark.
|
|
|
| SumiMark® Tubing for use with SumiMark® III & IV Machine Systems |
| SM3-12 |
Flexible Polyolefin 2:1 |
| SM3-13 |
Flexible Clear Polyolefin 2:1 |
| SM3-16 |
Flexible Chlorinated Polyolefin 2:1 |
| SM3-23 |
Flexible Overexpanded Polyolefin 3:1 |
| SM3-24 |
Adhesive Lined Flexible DualWall Polyolefin 2:1 |
| SM3-31 |
Very Flexible Polyvinylidene Fluoride 2:1 |
| SM3-41 |
Flexible Overexpanded Polyolefin 4:1 |
| SM3-60 |
Very Flexible Fluoroelastomer 2:1 |
| SumiMark® Ribbon for use with SumiMark® III & IV Machine Systems |
| SM3 |
Marking Ribbon |
| SumiMark® Tubing for use with SumiMark® I & II Machine Systems |
| SM12 |
Colors, UL(VW-1), CSA, 2:1 Shrink Ratio |
| SM23 |
Colors, UL(VW-1), CSA, 3:1 Shrink Ratio |
| SM24 |
Black & White, Adhesive Lined, 2:1 Shrink Ratio |
| SM31 |
Very Flexible Polyvinylidence Fluoride, 2:1 Shrink Ratio |
| SM48 |
Very Clear, Very Flexible, Fluorolymer, Skydrol Resistant |
| SM60 |
Black & White, 200°C Rated, Low Shrink Temperature |
| SumiMark® Ribbon for use with SumiMark® I & II Machine Systems |
| SR |
Marking Ribbon |
| The information contained in this brochure is believed to be correct and in accordance with accepted engineering practices. Because of the varied nature of the uses for these products each user should make their own evaluations regarding the suitability of these products for their specific application. Sumitomo Electric Interconnect Products, Inc. makes no warranties regarding the accuracy and completeness of the information and data contained herein, and disclaims any liability from the use or misuse of its products. Sumitomo Electric Interconnect Products, Inc. shall not be liable for any injury, loss or damage either directly, indirectly or as a consequence arising from the use or misuse of its products mentioned in this brochure, other than replacement of materials considered defective. |
|
|
|
| For further information please contact SEIP |
|
|
 |
1-800-758-3515
(US/Canada) |
|
1-760-761-0600
(Outside US/Canada) |
 |
E-mail SEIP |
|
|
|
 |
RoHS Compliance for SUMITUBE® Products |
|
|